Car Battery 6V or 12V charger  | 
       
     
    
    
      
         
  | 
       
     
    
      
           �����
        ������������ ���� �������� �� ��� ����� ��������
        �� ���������� ��� �������� ��� �����������. ����
        �� ������� ������ �� �������� ��������, �������
        ��� ����� ��������� 6V ��� 12V. ����
        ������� ���������� ���� �������� ����
        ���������� ��� ���������� ����� � �����
        ��������������� [�1] ����� ��������� �� ���� ����
        ������ ��� ������ ��� ��������������. �� Q1 ���� ���
        �������� R1-2, ��� TR1 ��� ��� R4,
        ���������� ��� ����������� ���� ��������. ��
        ����� ���� ��� R9 ������
        �� ���������� ������ Q5-6, ����
        ���������� �2000 ����� �������. �� ��� ���������
        �������� ����������� � ���� ����� 6 ��� 8V �������.
        �� ����� ��� �������� �� ����� �������� �����
        ������� 1.2� [���������� ��� �� TR1]. ���� �
        �������� ���������� ���� � ���� ��������� � ����
        ��� ���� ���. ��� 7V �������
        �� ���� � D1. ���
        ��������� � ���� ��� ��������� ����������� �
        ���� ��� ���� ��� R3 ��������
        �� Q1 ���
        �������. ���� ����������� ����� �� ����� ��
        ������ �� 6� �������. ���� ���� ��� ������ ������
        ��� ���� ��� R10, �������
        ������� �� Q4. �� �����
        ��� ���������� ��� ���� ��� Q5
        ���������, ����������� �� ����� ��������
        �������. ���� � �������� ��������� ������ [14.4V]
        �������������� �� ��������� ���� ��� ��������
        �������, ��� ����������� ��� ��� R6, D8, D2 ��� D6.
        ��������� ������ � D8 ���
        ������� ��� � �������� ���� ��������� ������.
        ���������� �� Q2 ���� ��
        ������ ��� ������ ����� ���� R6. �� Q3 �������
        ������� ��� ������� ����� ��� �������� ��� ����
        ��� Q5. ���� �
        ���� ��� ���� ��� ��������� ������ ������� ��� 15V �� �����
        ��� ���� ��� Q5 �����
        ���� �����, �� ���������� �� ���������� � �������
        ��� ���������. �� ������ D5-6
        ������������ �� ������� ��� ����� ���������� ���
        ��������� � ��� �������������� �������
        ���������. � ������ D4
        ����������� �� ������� ��� ����� ���������� ���
        ����� ��� ���������. ���� ������ � Led D9 �������
        �� ����� �������� [ERROR].
        ���������� ���  �������� S2
        ��������������� ��� ����� D2 [6.8V], ����
        �������� �� ���������� �������� 6V.  
        �������. 
           ��
        ������ ����� �������� ������ �� ��������� ����
        ��� TR1 ��� 1.2�. �
        ������� ������ �� ����� �� ��� �������� 6V.
        ��������� �� ����� �� ��� �������� ���
        ����������� [������� 10�]. ��� ��� �������
        �������� 6V,
        ��������������� ���� ��� ������������ ����
        ���������� ��� �������� ��� ���������� �� �� TR1 �� �����
        ��� 1.2�. ���� ��� ������� � ��������� S2 ������
        �� ����� ���� ���� ��� 12V, ������
        ��������. ��������� ������� ������ �� ����� ����
        �������� ��� ������ D2 ��� D3 �����
        ����� ������������ ��� �������� ���
        ������������. ��� � �������� ��� ����� �����
        ����� 100mV ������ ��
        ��� ���������� ��� ���������. ��� �����������
        ��������� ���� ������� ��� �������� ��� �� TR1 ���
        �����, �������� �� ���������� ��� ���� ���
        ���������� R4, ����� ��
        ��������� ����� �������� 1.2�. �� ��� ����������
        ����������� ��� ��������� ��� R10, ������
        �� ������������ �� �������� ��� �� �������� ���
        �� Q5-6, �����
        ������������. � ������ B1 ��� �� Q5-6  ������ �� ������������
        ����� �� ������ ���� �������� ��������� ��� ����
        �� �� ��������� ���� ���������. � ������ B1 ��� �
        ������� ���� �� ����������� �� ������� ������ ��
        ��������� �� ����� ��� ������ �������, ������
        ���� ��� �� ����� ����� ������. ������ �� �������
        ��� �������� ������ �� ����� �� ������� ������
        [��� ������ ��������� �� ��� ����� ������]. �
        ��������� ������ �� ����� �� ��� ���� ���������
        �����, ���������� ���������� ���� �� �������
        ����� ����������. � ��� ��������� ������� ���
        ������� ��������. � ������� ��
        ��������� ������� ���� ������ ������� ����
        ��������, ����� ������� ����� � �������� �������.
          | 
       
     
    
    
      
           Always we
        needed a charger with which we can charge the car battery. This circuit can charge
        automatically, fast and rightly, batteries 6V and 12V. A basic factor in the success in
        the circuit operation is the use of transformer [T1] of good quality with very good
        insulation and resistance in the short circuits. The Q1 via divider R1-2, the TR1 and the
        R4, functions as regulated current source. The current via the R9 drives the power
        transistors Q5 -6, where is strengthened X2000 times roughly. In a car battery charger the
        voltage is roughly 6V until 8V. With these conditions the charge current is roughly 1.2A
        [is regulated by TR1]. When the battery charge slowly, is increased her voltage in across.
        In the 7V it begins conduct the D1. As long as it�s increased the battery voltage is
        decreased the voltage in across the R3 making Q1 conductible. This continued as far the
        current reaches the 6A roughly. Then via the fall of tendency in utmost the R10, becomes
        driver the Q4. The current that in excess in base of Q5 grounded, confecting the current
        charge constant. When the battery charger [14.4V] is completely, activated the parallel to
        the battery circuit that is constituted by the R6, D8, and D2 until D6. Simultaneously
        turns on the D8 that shows that battery charged completely. Simultaneously Q2 turn on from
        cause of voltage fall in the R6. The Q3 becomes conductible and grounding some of current
        in the Q5 base. When the voltage across the battery reaches roughly in the 15V the current
        in the Q5 base is very small, so that stops the battery charging. Diodes D5-6 protect the
        circuit from error placement of battery or from short-circuit of big duration. Diode D4
        protects the circuit from error placement of poles of battery. Then Led D9 turns on shows
        the connection ERROR. Closing switch S2 short the diode D2 [6.8V], now we can charge a
        battery 6V.    | 
       
      
        Adjustment.
         
           The
        inceptive charge current should be adjusted via the TR1 in 1.2A. Adjust can become with a
        battery 6V. Connect in cascade with the battery a ampere meter [biggest 10A]. If does not
        exist battery 6V, sorted output charger via their ampere meter and we adjust with the TR1
        the current in 1.2A. At the regulation switch S2 it should they are in the 12V place, that
        is to say open. Attention should be given in the diodes D2 and D3 precision because these
        protect the battery from overcharge. If the voltage deviation is up to 100mV we believe to
        consider as acceptable. If you meet difficulties in the current adjustment and TR1 is not
        enough, you can change the resistance R4 value, until you measure charge current become
        1.2A. The two parallel resistors that constitute the R10, it should they are placed in
        distance by printed board and Q5-6, because they are heated. Bridge B1 and Q5-6 should be
        placed on heatsink after isolate electric from this with suitable silicone mica. Bridge B1
        and the PCB where it will be placed circuit should connected with near and fat cables,
        special there that the current are big. Also the lines in PCB should have proportional
        width [in the drawing they appear with far line]. The manufacture should become in a good
        metal box, suitable dimensions so that exists good ventilation. The all manufacture
        requires the proportional experience. The WORK WITH BATTERIES
        REQUIRES VERY BIG ATTENTION IN the HANDLING, BECAUSE EXIST ALWAYS the DANGER of EXPLOSION.    | 
       
     
    
      
         
  | 
       
     
    
    
      
        
          
            | R1-11=1K ohm
            0.5W 5% | 
            D3=4.7V 0.4W Zener | 
            C1=4700uF
            40V | 
           
          
            | R2=22K ohm 0.5W 5% | 
            D4-6-7=1N4148 | 
            C2=1uF 25V | 
           
          
            | R3-5-8=10K ohm 0.5W 5% | 
            D5=18V 0.4W Zener | 
            T1=230Vac//15V
            10A Transf. [See Text] | 
           
          
            | R4=2.2K ohm 0.5W 5% | 
            D8=LED 5mm Yellow | 
            F1=Fuse 1A
            Slo Blo [5X20mm]  | 
           
          
            | R6=100 ohm 0.5W 5% | 
            D9=LED 5mm Red | 
            S1=2X2
            Switch 10A per contact | 
           
          
            | R7=100K ohm 0.5W 5% | 
            Q1-2=BC557 | 
            S2=1X2 step mini switch | 
           
          
            | R9=470 ohm 0.5W 5% | 
            Q3-4=BC547 | 
            J1...4=Flat
            Pin Connector | 
           
          
            | R10=0.08 ohm 10W [2X0.18 ohm
            parallel] 5W | 
            Q5=BD139  
            [On Heatsink] | 
            J5=6pin Connector 2.54mm pin
            step | 
           
          
            | B1=Bridge
            Rectifier 25A/40V | 
            Q6=2N3055
            [On Heatsink] | 
            A=0-10A
            Ampere meter | 
           
          
            | D1-2=6.8V
            0.4W Zener | 
            TR1=4.7K
            Trimmer Pot. | 
            Batt=12V or
            6V Battery | 
           
         
         | 
       
     
    
    
      
          
        
          
            Sam
            Electronic Circuits 10/02  | 
           
         
         | 
       
     
     |