Intermittetly Pulse Generator

�� , �� . �� , �� , �� , �� . �� , �� . �� , ��, �� .�. �� 0V, �� , �� . � �� , �� . � �� 100��. �� 5Vpp (� 2.5V) �� . �� , �� RV1. � �� 5V, �� . �� S1, �� 1 ��10, (�� ), �� 1�� 10 �� , (�� 0V), �� 9 �� 0. � �� [1]-�� burst- �� .

�� ;

�� , �� S1 �� (��), �� 3, �� Q3 �� IC2/7. �� J1 �� 5V, �� S2, �� 3 �� IC1A �� J-K flip-flop �� , �� , �� 50%. �� , �� , �� 2. �� Q-IC1A/1, �� . �� CLK , �� IC2/14 �� C3A. �� IC2 �� . �� [H], �� . �� [�], �� Q1, �� , �� [L]. � �� [H], �� Q2, � �� Q3. � �� [H] �� Qo, �� , �� . � �� , �� flip-flop IC1B, �� IC3A. �� [�] �� +5V �� [0] �� -5V. �� S1, �� . �� S1 (�� 10), �� flip-flop IC1B �� RESET, �� . �� , �� : � �� Q2, �� Q3 �� , � �� Q2 �� Q3 �� . �� J2 �� RV1, �� R8, �� 600�. M�� , �� .� �� , �� IC3B-C-D. � �� , �� , �� S2. � �� S1, �� 10 �� , �� . � �� NiCd, �� . � �� zener. H.K 8.

Fig.1

Fig.2

The generators of square pulses, are used in a lot of applications, between which the adjustment of conditions of entry in the digital circuits and the control of amplifiers acoustic frequencies. This circuit is a generator that it produces, in combination with a other generator, sine wave frequencies or square pulses, continuous or interrupted square pulses. Main characteristic the generator it is, that the circle of operation can be regulated so as to he is constituted from until ten interrupted pulse. This pulses are particularly useful for the adjust amplifiers, loudspeaker, rooms of hearings etc. A other qualification of generator are that her pulses have level of report the 0V, without it is used for aim, capacitor in the exit. The absence of capacitor in the exit, has as result the production of clearly square pulses in any frequency of operation. The generator work without perceptible distortion up to their 100KHZ.Her pulses have width 5Vpp (� 2.5V) and cover the needs of all amplifiers acoustic frequencies. In the cases where we needed signal of smaller width, then we can him decrease with the pontesometer RV1. The generator is supplied with � 5V, provided from two batteries or from one suitable power supply. Placing the S1, in different places from the 1 until 10, (a place each time), the crowd of output pulses, in each circle of operation can be altered from 1 until 10 and the duration of pause, (when the signal is maintained in the level of 0V), from 9 until 0. The waveform [1] -acquaintance as burst - it is particularly benefit for the control of instability low or high frequency circuits.

How it works?

The circuit of generator that produces the interrupted square pulses and the produced vibrations in various points of circuit, when the selector of switch S1 is (ON), in the place 3, that correspond in exit Q3 of IC2/7. If in entry J1 we apply pulse line, width � 5V, then these via the S2, enter in the entry of 3 IC1A that is j-k flip-flop as T, with a view to it ensures in the circuits that follow, pulses with reason of duration to period 50%. Become division of frequency pulses, via 2. Thus in the exit Q-IC1A/1, are presented pulses with submultiples frequency. This pulses are applied in entry CLK, the IC2/14 and in a entry of IC3�. The IC2 is one decimal counter with decode exits. Each pulse of entry makes [ H ], one from his exits and concretely the one that corresponds in the content of enumeration. In the first pulse of entry, [ H ] becomes only exit Q1, of counter, while all the other are maintained in [ L]. The second pulse of entry makes [ H ], the exit Q2, third the Q3. The tenth pulse annihilates the content counter and it makes [ H ] the exit Qo, in order to is repeated the same circle of operation for the next pulses, entering pulse line. The number of pulses that will pass to the exit of generator is checked from counter, the flip-flop IC1B, and gate IC3�. In the particular application the logic [ H ] corresponds in + 5V and the logic [ 0 ] from the -5v. Proportionally the place that will be placed switch S1, is checked the number of pulses that will pass to the exit of generator. In the last place of S1 (place 10), flip-flop IC1B does not make RESET, so that are presented pulses continuity in the exit of generator. In the last place of S1 (place 10), flip-flop IC1B does not make RESET, so that are presented pulses continuity in the exit of generator. The output stage of generator, gives the three different levels of level that we needed: the output positive voltage it is created by the drive of Q2, in the satiation and Q3 in the cutting off, null from the cutoff of also two transistors and negative from the control of Q2 in the cutoff and Q3 in the satiation. The signal is applied in exit J2 via the pontesometer RV1, that with the R8, gives output impedance 600R. Can we change sine wave, triangular etc, signals in square pulses with the circuit of entry, that is constituted by the gates IC3B-C-D. The choice direct or transformation, the entering signals, becomes from switch S2. Switch S1, can be also replaced from a switching switch of 10 places, good quality. The supply becomes from two batteries NiCd, but can become also from suitable power supply. The essential stabilisation of voltage, becomes from the two diodes zener.

Part List